Extreme Performance
If you are looking for a high-quality subwoofer with the most accurate and precise in-vehicle subwoofer performance, then look no further. Alpine's 2nd generation state-of-the-art Type-X Subwoofers are your answer. With the advanced motor structure and new sound of these subs, you will experience higher efficiency, lower heat creation while maintaining superb sound, so you can really crank up the bass.

New Aerospace Cone Material
The Type-X cone uses new advanced aerospace materials such as Kevlar-Rohacell® parabolic cone for outstanding strength and light weight. These lighter materials minimize moving mass for greater output efficiency than ever before.

HAMR Engineering
Type-X subs are built with HAMR engineering, Alpine's exclusive subwoofer solution for cooler operation, longer life and tight accurate bass. Type-X subs are the way go.

Features

• Power Handling
  Power Range: 500 - 1000 Watts
  RMS Power Handling: 1000 Watts
  Peak Power Handling: 3000 Watts
• Dimensions
  Mounting Depth: 219 mm (8.6'')
  Mounting Diameter: 277 mm (10.9'')
  Displacement: 0.194 cu. ft. (Front Mount)
  Added Volume: 0.079 cu. ft. (Reverse Mount, Magnet Out)
• General
  Frequency Response: 24Hz - 200Hz
• Diaphram
  Material: Kevlar RohacellA? Layered Composite
  Design: 1-Piece Parabolic wtih Vented Force Transfer Assembly
• Surround
  Material: Injection Molded SantopreneA?
  Design: High Amplitude Multi-Roll (Patent Pending)
• Spider
  Material: NomexA?
  Design: Mirrored Progressive
• Voice Coil
  Material: 220A?C Aluminum Wire on Twin-Wall Aluminum Former (Patent #6,292,079)
  Design: 6-Layer 4I? Voice Coil with Inner/Outer Winding
• Motor Structure
  Pole Geometry: Compound Radius Curve (Patent #6,639,993) with T-Drive
  Configuration: Billet Copper Shorting Sleeves with Heat Dissipation Plate (Patent Pending)
• Frame
  Material: Cast Aluminum
  Design: Perimeter Vented Exo-Frame (Patent Pending) with Integrated Spider Landing (Patent #6,678,387)
• Terminals
  Layout: One Side
  Design: Insert Terminal Blocks with High Current Voice Coil Configuration Jumper
• Tinsel Leads
  Design: Reinforced Layer Spider Integration (Patent #6,810,988)
• Gasket
  Design: Concealed Mount Design with Front/Rear Sealing Gaskets

Extreme Performance
If you are looking for a high-quality subwoofer with the most accurate and precise in-vehicle subwoofer performance, then look no further. Alpine's 2nd generation state-of-the-art Type-X Subwoofers are your answer. With the advanced motor structure and new sound of these subs, you will experience higher efficiency, lower heat creation while maintaining superb sound, so you can really crank up the bass.

New Aerospace Cone Material
The Type-X cone uses new advanced aerospace materials such as Kevlar-Rohacell® parabolic cone for outstanding strength and light weight. These lighter materials minimize moving mass for greater output efficiency than ever before.

HAMR Engineering
Type-X subs are built with HAMR engineering, Alpine's exclusive subwoofer solution for cooler operation, longer life and tight accurate bass. Type-X subs are the way go.

Features

• Power Handling
  Power Range: 500 - 1000 Watts
  RMS Power Handling: 1000 Watts
  Peak Power Handling: 3000 Watts
• Dimensions
  Mounting Depth: 218 mm (8.6'')
  Mounting Diameter: 231 mm (9.1'')
  Displacement: 0.162 cu. ft. (Front Mount)
  Added Volume: 0.062 cu. ft. (Reverse Mount, Magnet Out)
• General
  Frequency Response: 26Hz - 200Hz
• Diaphram
  Material: Kevlar RohacellA? Layered Composite
  Design: 1-Piece Parabolic with Vented Force Transfer Assembly
• Surround
  Material: Injection Molded Santoprene
  Design: High Amplitued Multi-Roll (Patent Pending)
• Spider
  Material: Nomexa
  Design: Mirrored Progressive
• Voice Coil
  Material: 220A?C Aluminum Wire on Twin-Wall Aluminum Former (Patent #6,292,079)
  Design: 6-Layer Dual 4I? Voice Coil with Inner/Outer Winding
• Motor Structure
  Pole Geometry: Compound Radius Curve (Patent #6,639,993) with T-Drive
  Configuration: Billet Copper Shorting Sleeves with Heat Dissipation Plate (Patent Pending)